Skip to main content

Phones answered 24/7 · Long Island, NY

Appliance repair FAQ

The questions Long Island callers put to our dispatch desk again and again: what is wrong with the machine, what it will cost, how the warranty works and whether we reach your town. Each answer sits below or a single link away.
  • Off labor$10First repairNew PrimeFix customers
  • Off labor$15Repeat customerBooked with us before
  • Off labor$15MilitaryServing, veterans & families
  • Off labor$10Over 65Customers aged 65 and up

Answered 24/7Three-hour arrival window90-day parts warranty

Diagnosis
The fault is found before anything is quoted
Approval
Work starts only after your yes
Hours
Phones answered 24/7
Warranty
Parts 90 days · labor 30 days

Request a Repair

Two short steps. No cost and no obligation to book.

  • Answered 24/7
  • 3-hour arrival window
  • Price approved first
Step 1 of 2

The repair

Which appliance needs repair?

Appliance

Where are you?

Free to book. No payment details needed.

Rather speak to someone? (631) 729-9995

Not listed?

Our phones are answered 24/7, nights included.

13 questions · answered here

Is it repairable?

Faults we hear about before anyone books — the usual cause behind each one, and what putting it right actually takes.

  1. Can you repair a stove top burner that won't light or heat?

    Yes. On gas, a burner that sparks but does not catch generally has a dirty igniter, clogged burner ports or a weakening spark module, whereas no spark at all suggests the switch or the module itself. On electric, a burner that stays cold comes down to the element, its terminal block or the infinite switch behind the control knob. Each is a standard single-visit job when the part is carried on the van. Should you ever smell gas, leave the room without operating any switch and contact your gas utility first.

  2. Can you repair a washer that won't spin?

    Yes — it is among our most frequent calls. Most machines that refuse to spin are in fact failing to drain: a clogged pump filter, a stray sock lodged in the pump or a kinked drain hose will halt the spin long before any motor gives out. Next in line are the lid or door lock, a stretched belt on belt-drive models and, more rarely, the motor control board. Draining is ruled out first because it is the least expensive cause.

  3. Can you replace a dryer heating element?

    Yes. Elements are a frequent replacement on electric dryers, but they rarely fail on their own account: a choked exhaust makes the element run too hot until it breaks or trips the thermal limit. We therefore fit the new element and then inspect the duct all the way to the exterior wall, otherwise the replacement will suffer the same fate. On gas dryers the equivalent components are the igniter, the flame sensor and the gas valve coils.

  4. Can you repair a refrigerator or freezer door gasket?

    Yes. A seal that is split, compressed flat or coming away admits warm, humid air, and that appears as frost, condensation along the door edge or a compressor that runs without pause. Occasionally the remedy is reseating the seal or correcting a drooping door rather than replacing it. Where a new gasket is required, we order the exact one for your model, so sending a photo of the model label at booking avoids a second trip.

  5. Can you repair an ice maker that no longer makes ice?

    Yes, whether it is built into a refrigerator or is a freestanding undercounter machine. Common causes are an iced-up fill tube, a failed water inlet valve, a blocked filter or a control module that has stopped cycling. We check the water reaching the unit first, since a partly shut valve behind the refrigerator mimics a failed ice maker perfectly.

  6. Can you repair a microwave that runs but won't heat?

    In many cases. If the turntable rotates and the lamp lights but food stays cold, the fault is on the high-voltage side — typically the diode, the capacitor, the magnetron or a door interlock switch. Those circuits can retain a lethal charge even when unplugged, so this is not a job for a homeowner. On a small countertop unit the repair may approach the cost of replacing it, and if so we will tell you.

  7. Can you replace dishwasher door springs?

    Yes. A door that falls open or will not hold its position nearly always has a broken spring or a snapped hinge cable. Springs are fitted in pairs, since the remaining one is the same age and close behind. It is a quick repair, although some models must be eased out of the cabinet to get at them.

  8. Can you repair a wine cooler that won't hold temperature?

    Yes, both compressor and thermoelectric types. With compressor models the typical causes are a dust-clogged condenser, a dead fan, a faulty start relay or, less commonly, a slow refrigerant leak. Thermoelectric coolers rely on a Peltier module and its fans and are inherently limited in a warm room. Built-in units frequently fail for no reason other than an obstructed front grille that prevents them from venting.

  9. Can you repair a refrigerator compressor?

    In some cases. A compressor that appears dead often turns out to have a failed start relay, overload protector or driving inverter board, and those are simple parts to replace. A compressor that has truly failed requires recovering the refrigerant, brazing in a replacement and recharging the system under EPA Section 608 rules, which is a substantial job. On an ageing mass-market refrigerator that can exceed what the appliance is worth, and we tell you so before you commit.

  10. Can you repair a cracked glass cooktop?

    Generally yes, by fitting a new glass top instead of replacing the entire cooktop. On most radiant and induction designs the glass is a separate component, and it has to be the precise part for your model because the elements and sensors sit directly beneath it. Until it is replaced, do not use the cracked surface: spills can find their way through to live components.

  11. Can you repair a washer drum that bangs or won't turn?

    Yes. Knocking during spin is generally caused by worn suspension springs or shock absorbers on top-loaders, or by failed drum bearings on front-loaders, which also rumble loudly as they accelerate. Bearings are the more involved repair since the tub must be dismantled, so on an older washer we compare that cost with replacement before beginning.

  12. Can you repair a dryer drum that won't turn?

    Yes. When the motor hums and the drum does not move, the drive belt has usually broken or come off its pulley; when there is no response at all, we check the door switch and thermal fuse first. Worn drum rollers and idler pulleys tend to squeal for weeks before seizing. Belts, rollers and fuses are all stocked on the van.

  13. Do you service induction cooktops and ranges?

    We do. Induction failures are largely electronic — a power board, a coil temperature sensor, a cooling fan or the glass touch control — and many announce themselves with an error code first. Give us the code and the model number when you phone, and we can frequently identify the probable part in advance so that it is already on the van.

Does this describe yours?

8 questions · answered here

Mend it or buy new?

Typical service lives by appliance, and where the arithmetic tips in favor of buying new.

  1. Should a refrigerator be repaired?

    Generally yes, where the fault lies in a fan, a defrost component, a thermostat or a control board. Industry figures suggest a refrigerator lasts roughly 13 years. Our guideline is straightforward: when the repair approaches half the cost of a similar new model and the unit has passed two-thirds of its expected life, replacement is the better purchase, and we will say so. Built-in and panel-ready refrigerators are the exception and are nearly always worth repairing.

  2. What is a dishwasher's lifespan, and is repair worthwhile?

    Estimates usually put it at nine to ten years. Within that time, pumps, door springs, latches, inlet valves and heating elements are all sensible replacements. Beyond it, a failed control board or a leaking tub generally signals the moment to replace. Public water on Long Island is mostly soft to moderately hard, so dishwashers here tend to wear rather than scale; in high-iron areas, staining and clogged filter screens are the more usual complaint.

  3. Should a dryer be repaired?

    Almost always, since dryers are mechanically simple. They generally last about 10 to 13 years, and their usual failures — belts, rollers, thermal fuses, elements, igniters — are cheap parts. The exceptions are a drum that has rusted through or a dead main board on a very old machine. Swapping a dryer without clearing an obstructed vent merely passes the problem to the replacement.

  4. What is a washing machine's lifespan, and when is replacement better?

    Ten years is the figure most often quoted, and fewer for a machine running every day for a big family. Drain pumps, lid and door locks, belts and inlet valves are ordinary repairs well worth making. Failed bearings on an older front-loader, or a split outer tub, is generally the point at which a new washer is the wiser spend.

  5. Should an oven, stove or range be repaired?

    In most cases, yes. Cooking appliances frequently last 13 to 15 years, and their typical faults — igniters, bake elements, temperature sensors and switches — involve inexpensive parts. Gas ranges in particular usually outlive their electronics, so replacing the control board on an otherwise sound range is often money well spent. Dual-fuel and professional-style ranges almost always justify repair.

  6. Is an over-the-range microwave worth repairing?

    More often than a countertop model is. An over-the-range microwave doubles as your ventilation hood and is fixed to the cabinets, so a door switch, diode, magnetron or fan replacement is usually cheaper than a new unit plus installation. These typically last about nine years. A countertop microwave that will not heat, on the other hand, is frequently cheaper to replace.

  7. Should a freezer be repaired?

    Chest and upright freezers often run 11 years or longer, and thermostat, defrost, fan or door-seal faults are worth correcting at nearly any age. The usual exception is a failed compressor in an older freezer. Until the technician arrives, keep the door or lid closed: a full freezer stays cold far longer than one that is half empty.

  8. Should a wine cooler be repaired?

    If it is a built-in or dual-zone model fitted into cabinetry, generally yes, because a replacement must match the existing opening. With a small freestanding thermoelectric cooler, a dead module can cost almost as much as a new unit. Compressor-type coolers with a fan, relay or thermostat fault are sound repairs at most ages.

Want an honest verdict on your machine?

4 questions · answered here

Where on Long Island we work

The towns and ZIP codes we cover, how visits are grouped into routes, and the single calendar date that upsets all of it.

  1. Is all of Long Island covered?

    Our coverage takes in 119 ZIP codes in Nassau and Suffolk County — starting at the Queens border with Great Neck, Floral Park and Franklin Square, running through Hempstead, Hicksville, Levittown and Massapequa, and reaching Huntington, Hauppauge, Patchogue, Stony Brook and Wading River in Suffolk.

  2. Are both the North Shore and the South Shore served?

    Both are. On the North Shore, vans follow 25A through Roslyn, Glen Cove, Oyster Bay, Huntington, Northport and Port Jefferson; on the South Shore they work Sunrise Highway and Merrick Road from Lynbrook and Freeport by way of Massapequa, Babylon and Bay Shore out to Patchogue and Bellport.

  3. Are repair vans allowed on the parkways?

    They are not — Long Island's parkways are closed to commercial vehicles, so our vans travel the Long Island Expressway, Sunrise Highway, Jericho Turnpike, Hempstead Turnpike and Route 25A instead. That is part of why we offer a realistic arrival window rather than an exact time.

  4. Do you work in houses that were raised after Hurricane Sandy?

    We do. Elevated South Shore homes commonly have extended dryer ducts, laundry moved to a new floor and fresh gas and water lines, so we inspect the installation as well as the appliance; a machine relocated upstairs is often sound while its hook-up is not.

We serve 28 areas spanning 119 ZIP codes in Nassau and Suffolk. Look up your town in the full list of service areas.

Unsure whether we reach your street?

15 questions · answered here

Your appliance

The complaints behind most of our visits, and the diagnosis each tends to end in. A few of them describe an appliance with nothing wrong at all.

  1. The freezer is cold but the fridge section is warm — is the refrigerator finished?

    Seldom. That pattern almost always points to a problem with airflow or defrosting, not to a failing compressor: cold is still being produced in the freezer but is no longer getting through to the fresh-food side. Typically the evaporator has frozen solid because the defrost heater has stopped melting it, or the evaporator fan has died. Each of these sits at the affordable end of refrigeration repair, and each is frequently mistaken for compressor failure.

  2. What does a refrigerator repair typically cost on Long Island?

    Fan, defrost and airflow faults usually fall somewhere in the low to middle hundreds. Sealed-system repairs — a refrigerant leak, a blockage in the tubing, a dead compressor — come in considerably higher, and on a mass-market model beyond two-thirds of its lifespan they are seldom a good investment. The diagnosis tells you which category your fault belongs to before you are committed to any cost.

  3. Why does the spare fridge in my garage keep breaking down?

    Ordinary household refrigerators are designed to sit in a heated, cooled room, and a Long Island garage falls outside that range in both summer and winter. During August heat the condenser struggles to reject heat, so the compressor runs continuously; in January cold a model with a single thermostat senses that the fresh-food compartment is already chilled, stops cooling, and leaves the freezer to thaw with no fault showing. Units rated for garage use are built for these swings, and no repair can give that rating to a standard model.

  1. The washer won't spin — has the motor failed?

    Not usually. When a machine refuses to spin, the underlying problem is more often that it cannot drain, and it is designed not to spin with a tub of water in it. Look at the drain filter first; a blockage there causes many more no-spin calls than a motor or control board ever does. If draining is not the issue, the door or lid switch comes next, followed by the drive coupling.

  2. What are error codes actually telling me?

    A code describes a condition the machine has sensed, not the part responsible for it. A fill code says the water expected did not arrive, and the reason might be low supply pressure, a clogged inlet screen, a scaled-up valve or a level sensor giving a false reading. For that reason we diagnose the machine rather than order whichever part the code appears to point at.

  3. What causes a washer to smell?

    Water left standing where it should have drained — in the sump, the filter or the drain hose — together with a film of bacteria on the door seal. Front-loading machines suffer more because their seal stays damp from one wash to the next. The root is a drainage and sealing fault, and if it is ignored it tends to develop into a more serious one.

  1. Why did the new heating element fail like the old one?

    Because the element was never the real problem. A dryer is essentially a blower with a heater in its path; choke the exhaust and the heater keeps tripping its thermal limit until it burns out. A fresh element installed behind the same blocked vent will fail in just the same way. We take an airflow measurement instead of assuming, and if the duct run is simply too long for the machine, we tell you.

  2. What does a dryer repair usually cost?

    Dryer work is generally among the cheaper repairs: thermal fuses, limit switches, belts, idler pulleys, igniters and elements are inexpensive parts with uncomplicated labor. The cost rises when the real problem lies in the ductwork rather than the dryer, because that belongs to a different trade and no dryer component will cure it.

  3. Why does one load need three cycles to dry?

    Nearly always restricted airflow. In split-levels and raised ranches the duct frequently travels through a joist cavity or a crawlspace before reaching an outside wall, and a home lifted after Sandy may have gained several extra feet of duct. Combine that with a flattened foil connector behind the dryer and lint compacted at the first bend, and the dryer receives only a small share of the air it needs, even though the heater is working exactly as it should.

  1. Why are my dishes still wet — has the heating element gone?

    On a Bosch, Miele, Asko or most other European designs there is no heating element for drying at all; these machines rely on moisture condensing on the cool stainless tub. Plastics that stay damp and dishes that come out cool are how the machine is meant to behave. It is easily the most frequent call we attend where nothing is actually wrong.

  2. What leaves a white film on glasses?

    Island households draw groundwater from Long Island's aquifers, and across most of Nassau and Suffolk it ranges from soft to moderately hard, so a cloudy film on glassware usually comes from too much detergent or rinse aid rather than genuine scale. When local water really is to blame, the culprit tends to be iron or manganese, which stains the tub orange or brown instead of leaving a white residue. During the visit we test the supply and, on models that allow it, set the hardness level to suit.

  3. The upper rack isn't getting clean.

    That symptom implicates the diverter or the feed to the upper spray arm, not the main pump. The top rack is only washed if water is actually directed up to it, so a faulty diverter or a blocked supply produces just this result while the bottom rack comes out clean. We confirm the arms turn freely and their jets are clear before blaming the circulation pump.

  1. The oven runs cool although the element seems fine.

    There are two usual reasons to check before the element. One is calibration: the control is regulating properly but around a set point that has wandered, which on most models is corrected by adjustment, not a part. The other is the door, where a perished gasket or worn hinge springs let heat escape faster than the element can make it up — and that looks just like a heating failure.

  2. What does an oven repair usually cost?

    Temperature sensors, elements and igniters are reasonably priced and simple to fit, so the typical oven repair falls within the low to middle hundreds. Wall ovens built into cabinetry cost more to service than freestanding ranges, since removing them safely is a real part of the work — and that same difficulty shifts the repair-or-replace balance strongly in favor of repair.

  3. I can smell gas from the oven. What now?

    Turn it off, leave it alone and phone us. A smell of gas means fuel is escaping into the kitchen instead of burning at the burner, and nothing else should be investigated until that is resolved. We close the appliance's shut-off and test every connection with a leak detector. If the fault lies in the house supply rather than the oven, we explain that and leave the appliance shut off, not reconnected.

Don't see your appliance here? Each one we service has a page of its own covering its most frequent faults.

Seeing a symptom we have not covered?

2 questions · answered here

Managed buildings, paperwork and refrigerant

Co-op and condo boards, building access, gas connections and refrigerant rules — what a managed property wants settled before any contractor arrives.

  1. Can you work in apartment buildings, co-ops and condominiums?

    Certainly. Managed buildings and co-ops in Great Neck, Mineola, Rockville Centre, Garden City and similar communities, along with Suffolk's condominium developments, often set access hours and ask for contractors to be announced in advance. Name the building when you phone and mention any elevator or service-entrance reservation it requires, and the visit is arranged around it.

  2. Do you also repair commercial kitchen equipment?

    We do. Besides household appliances, we look after commercial refrigeration, ice machines, reach-in units, prep tables and cooking lines. These jobs are triaged on their own terms — an ice machine or walk-in that has stopped is a loss of revenue, not merely a nuisance — and where the kitchen can accommodate it, we arrange the visit around service.

Does your building need documents first?

6 questions · answered on its own page

Booking, pricing and warranty terms

How quickly we arrive, how the single quoted price works, late-night calls and the exact terms of the warranty.

Each repair carries a 90-Day Parts & 30-Day Labor Warranty. The booking sequence is laid out stage by stage on the contact page, ending with the warranty.

Ready to book a visit?

4 questions · answered on its own page

Household equipment

Getting in, protecting your floors, paperwork for building staff and adding a second machine to one visit.

Narrow stairs or a cramped landing?

5 questions · answered on its own page

Restaurant and business kitchens

Where a kitchen sits in the queue, working around service hours, stocked brands and the records you can keep on file.

A kitchen line down before service?

Something else

Bring us the unusual question

No list covers everything. A discontinued model with scarce parts, a stairwell where a fridge will not make the turn — situations like these are settled faster in a short phone conversation.

Call now(631) 729-9995Book online