Skip to main content

Phones answered 24/7 · Long Island, NY

Ice Maker Repair Near Me, Across Long Island

Ice Maker repair on Long Island for 9 brands, roughly 1–2 hours at your home.

How the visit is charged

The diagnostic fee is credited against the repair

  • Off labor$10First repairNew PrimeFix customers
  • Off labor$15Repeat customerBooked with us before
  • Off labor$15MilitaryServing, veterans & families
  • Off labor$10Over 65Customers aged 65 and up

Answered 24/7Three-hour arrival window90-day parts warranty

Lines open 24/7 · 3-hour window
Diagnosis
The fault is found before anything is quoted
Approval
Work starts only after your yes
Hours
Phones answered 24/7
Warranty
Parts 90 days · labor 30 days

Request a Repair

Two short steps. No cost and no obligation to book.

  • Answered 24/7
  • 3-hour arrival window
  • Price approved first
Step 1 of 2

The repair

Which appliance needs repair?

Appliance

Where are you?

Free to book. No payment details needed.

Next: a dispatcher phones you to fix a three-hour arrival window. Rather talk now? (631) 729-9995

  • EPA 608 refrigerant handling
  • 90-Day Parts & 30-Day Labor Warranty
  • Open 24/7
  • 119 ZIP codes covered

The ice maker in figures

Usual visit length
1–2 hours
Faults on file
40
Makes we work on
9

Anatomy · Ice Maker

The parts of a ice maker that wear out first

Ice machine: water path and refrigeration loop
This drawing shows a self-contained cuber. Nugget and flake models do without the evaporator mold and hot-gas valve (5, 6), using an auger that turns inside a refrigerated barrel, and a refrigerator's built-in icemaker relies on a fill valve, mold and ejector arm in the freezer instead of a recirculating sump.
  1. 01
    Water inlet valve and screenA clogged screen underfills the sump, producing small or hollow cubes that owners describe as the machine 'making less ice'.
  2. 02
    Water filterOnce past its rated life it removes nothing and begins adding off-tastes of its own.
  3. 03
    Water pumpWeak circulation never wets the plate evenly, giving thin, hollow and inconsistent cubes.
  4. 04
    Distribution tubeScale closes the outlets one by one, so some cube cells fill while others stay empty.
  5. 05
    Evaporator moldScale insulates the plate, so each batch takes longer to freeze and yields less, until the ice no longer releases.
  6. 06
    Hot-gas harvest valveIf it does not open at harvest, the batch stays frozen to the plate and the cycle never ends.
  7. 07
    Bin level controlThe curtain or sensor that reports a full bin; stuck one way the machine never stops, stuck the other it never starts.
  8. 08
    Condenser coilWith little air under a counter it clogs quickly, which is why output drops first in summer.
  9. 09
    Condenser fanA slowing fan lengthens freeze cycles and makes the machine noisier than it used to be.
  10. 10
    CompressorStruggles to start on hot days and then gives up. It is condemned last, once water and airflow are cleared.
  11. 11
    Drain and drain pumpA clogged drain pushes meltwater back into the bin and fuses the ice into clumps; on pumped installations the pump is the usual first failure.

Sequence of checks

Where a technician starts on a ice maker

What we test, in turn
the water supply is checked first, then the fill valve, then the harvest assembly — slow production and hollow or cloudy cubes come from supply and scale far more often than from a failed module
The symptom owners misjudge
an ice maker written off as dead when the water line behind the appliance is kinked or the inlet screen has clogged with mineral deposit
Why Long Island matters here
the gap between soft public groundwater, iron-laden supply and private wells, which shapes ice-maker life more than anything else on both household and commercial units and determines whether the inlet screen gathers sediment, scale or nothing

Fault register · 40 entries

The ice maker failures behind most of our calls

  1. 01

    No Ice Being Produced

    The bin is empty or holds only old, fused ice, and the machine may be silent or running without result. Production depends on water arriving, the refrigeration cooling the plate and the control running a harvest, so any break in that chain stops it.

    Likely origins
    water supply valve closed or line frozen · failed water inlet valve · bin sensor reading full · compressor or condenser fan not running · control board not starting a cycle
    The fix
    We confirm water reaches the machine and the sump fills, then check whether the compressor and fans run and the plate gets cold. The bin sensor and control are tested to see whether the machine believes it should be producing. Once the break in the chain is located, that part is renewed. We stay through a complete freeze and harvest to confirm ice drops into the bin.
  2. 02

    Ice Production Falling Short

    The machine makes ice, but noticeably less than it used to, and the bin rarely fills. Freeze cycles are taking longer, or harvests are leaving ice behind.

    Likely origins
    scale on the evaporator plate · dirty condenser coils · high room temperature · low water flow from a partly blocked inlet · weak harvest valve
    The fix
    We time a freeze and harvest cycle and compare it with the manufacturer's figures for the room and water temperatures. The condenser, evaporator and inlet screen are inspected for build-up. We descale the water system and clean the condenser where needed, and test the harvest valve. A second timed cycle confirms production has recovered.
  3. 03

    Water Pooling Under the Machine

    Water collects on the floor beneath or in front of the ice machine. It may be supply water escaping at a connection, or drain water that is not leaving the cabinet as designed.

    Likely origins
    loose compression fitting on the supply line · drain line disconnected or kinked · drain pump failed on pumped models · cracked sump or bin drain · condensate overflowing
    The fix
    We dry the area, then run a fill and a harvest while watching the supply connection, the bin drain and the pump outlet to see exactly where water appears. Fittings are remade, kinked lines rerouted and cracked parts replaced. On pumped installations the drain pump is tested. The floor is checked after several cycles to confirm it stays dry.
  4. 04

    Ice Tasting of Chlorine or Minerals

    The ice carries a chemical, metallic or earthy taste that comes through in drinks. In most cases the taste is already in the supply water, and the freezing process concentrates it.

    Likely origins
    water filter cartridge exhausted · no filter fitted · chlorine or chloramine in the municipal supply · iron or sulphur in well water · new supply line or plumbing taste
    The fix
    We taste and test the supply water at the machine, then check the filter's age and fit. An exhausted filter is replaced, or a suitable filter recommended for your water. The machine is descaled and sanitized, and the first bins of ice are discarded. Ice made after the work is checked for taste.
  5. 05

    Cubes Thin or Undersized

    Cubes come out thin, small or uneven at the edges, and the bin fills with fragments. The plate is receiving too little water, or the control is calling harvest before the slab has fully formed.

    Likely origins
    low water level in the sump · partly blocked inlet screen · ice thickness probe set too thin · distribution tube partially blocked · water pump weakening
    The fix
    We watch a freeze cycle to see whether water covers the full plate, then check the sump level, inlet screen and distribution tube. The ice thickness probe or setting is inspected and adjusted to the manufacturer's bridge thickness. Blockages are cleared and worn parts replaced. A complete harvest shows full, evenly formed cubes.
  6. 06

    Condenser Coils Restricted by Dust

    The condenser gets rid of the heat removed from the water. Lint, dust and grease on its fins slow that process, lengthening freeze times and raising compressor temperature.

    Likely origins
    dust and lint drawn in through the front grille · kitchen grease in the air · undercounter installation with poor airflow · pet hair · no routine cleaning
    The fix
    We disconnect power and clean the condenser fins with a brush and vacuum, working in the direction of the fins to avoid flattening them. The condenser fan is checked for speed and blade condition. Ventilation around the unit is reviewed, since a blocked grille has the same effect. Freeze time is measured after cleaning.
  7. 07

    Scale Coating the Evaporator Plate

    A white or tan crust builds up on the plate or grid where the ice forms. It insulates the plate, slows freezing and makes the ice stick during harvest.

    Likely origins
    hard water without treatment · descaling overdue · no water filter fitted · filter cartridge exhausted · high mineral content from a private well
    The fix
    We run the manufacturer's descaling procedure with a nickel-safe cleaner, removing the distribution tube and sump parts for separate cleaning. The plate is inspected to make sure scale has been fully removed without damaging its coating. A sanitizing cycle follows. We discuss water treatment and a descaling interval suited to your water.
  8. 08

    Water Inlet Valve Not Opening or Closing

    The inlet valve controls water into the sump. If it fails to open, the machine cannot fill; if it fails to close, water runs continuously to the drain.

    Likely origins
    valve coil open · sediment on the inlet screen · valve diaphragm worn · low supply pressure · control not powering the valve
    The fix
    We measure the coil resistance and check for voltage during the fill phase, then inspect the inlet screen for sediment. A failed valve is replaced and the screen cleaned. Water pressure at the supply is confirmed. A full cycle shows the valve opening for fill and closing reliably afterwards.
  9. 09

    Cloudy Instead of Clear Ice

    Cubes come out white or milky rather than clear, sometimes with a chalky core. Air and dissolved minerals are being trapped as the water freezes instead of being washed away by the flow across the plate.

    Likely origins
    high mineral content · water not circulating properly · scale on the plate · freeze too fast · low water flow
    The fix
    We test hardness and dissolved solids in the supply, then watch the water pattern over the plate during a freeze, since weak circulation traps air. The water system is descaled and the filter replaced or upgraded where the supply calls for it. The purge setting is reviewed on machines that offer one. Clarity is assessed again over several harvests.
  10. 10

    Circulation Pump Not Running

    The pump that lifts water from the sump to the distribution tube has stopped. The plate stays dry or receives only a trickle, and no proper ice forms.

    Likely origins
    seized pump motor · impeller blocked by scale · failed motor winding · loose connector · control not powering the pump
    The fix
    We confirm the control powers the pump during the freeze, then remove it to inspect the impeller and motor shaft. Scale packing the impeller is cleared; a pump with an open winding or seized bearing is replaced. After refitting, we watch the flow across the full width of the plate and time a freeze cycle against the specification.
  11. 11

    Ice Not Releasing at Harvest

    Ice stays frozen to the plate or mold after harvest begins, and some machines lock out after several failed harvests in a row. Either the surface is not warming enough, or scale is gripping the ice.

    Likely origins
    scale on the plate · hot-gas valve failing · harvest assist mechanism fault · thermistor ending harvest early · machine out of level
    The fix
    We watch a harvest closely to see whether the plate warms and whether the slab starts to slide. The hot-gas valve and any harvest-assist mechanism are tested, and the machine levelled so ice can fall cleanly. The plate is descaled where deposits are holding the ice. Failed parts are replaced, and a run of consecutive harvests confirms clean release.
  12. 12

    Stale or Musty Ice

    Ice smells or tastes stale, musty or of other foods, even though the water itself tastes clean. Biofilm in the water system or odours absorbed in the bin are the usual sources.

    Likely origins
    biofilm in the sump, pump or tubes · bin not cleaned regularly · ice left sitting too long · odours drawn in from the room · drain trap allowing sewer air back
    The fix
    We inspect the sump, pump, tubing and bin for slime, then run a full clean and sanitize with an approved cleaner. The drain is checked for an air gap and trap so sewer air cannot return. Old ice is discarded. We advise on a sanitizing interval, and ice made afterwards is checked for odour.
  13. 13

    Distribution Tube Blocked

    The tube that spreads water across the evaporator has blocked outlet holes. Parts of the plate receive little water, so the ice there forms thin, misshapen or not at all.

    Likely origins
    mineral scale in the outlet holes · biofilm in the tube · debris from the supply · descaling overdue · tube cracked
    The fix
    We remove the tube and soak it in a nickel-safe descaler, clearing each outlet hole individually. A cracked or deformed tube is replaced rather than cleaned. The tube is refitted in its locating clips and the water pattern observed across the plate. A full harvest confirms that cubes now form evenly from edge to edge.
  14. 14

    Machine Keeps Running With a Full Bin

    Ice piles up against the door or curtain because production does not stop when the bin is full. The bin sensor or thermostat is not detecting the ice.

    Likely origins
    bin thermostat bulb out of position · bin sensor failed · sensor lens dirty · control fault · bin switch stuck
    The fix
    We check the bin sensor or thermostat bulb is in its proper position and clean any film from its lens or surface. The sensor and the control's response to it are then tested. A failed sensor, switch or control is replaced. We let ice reach the sensor and confirm that production stops and resumes as the bin is emptied.
  15. 15

    Drain Pump Not Clearing Water

    On machines without a gravity drain, a pump lifts meltwater to the drain. When it fails, water backs up into the bin or onto the floor.

    Likely origins
    seized pump motor · blocked pump inlet · float switch stuck · drain line blocked · power fault
    The fix
    We test the pump motor and its float switch, clear debris from the inlet and check the discharge line for kinks or a blocked check valve. A failed pump is replaced. Water is then poured into the reservoir to confirm the pump starts at the correct level and empties it completely to the drain.
  16. 16

    Hot-Gas Harvest Valve Not Opening

    During harvest, a solenoid valve diverts hot refrigerant gas through the evaporator so the ice loosens. If that valve fails to open, the plate stays cold, harvest drags on and ice remains stuck until the machine gives up.

    Likely origins
    failed harvest valve coil · valve stuck closed internally · control not energizing the valve · loose connector at the coil · refrigerant restriction
    The fix
    We confirm the control energizes the harvest valve and measure the coil's resistance, then feel the evaporator inlet line for the warming that should follow. A failed coil is replaced, and a valve body that will not open is replaced with refrigerant recovered under EPA Section 608. Several harvest cycles are then timed to confirm the ice releases promptly.
  17. 17

    Louder Than Normal in Operation

    The machine has become noticeably noisier, with grinding, rattling or a high-pitched whine. Some sounds, such as the harvest drop and water flow, are normal; new ones usually come from a fan, pump or loose panel.

    Likely origins
    condenser fan blade striking debris · worn water pump bearing · loose panel or mounting · compressor mounts worn · ice striking the curtain at harvest
    The fix
    We run the machine through freeze and harvest and locate the noise by stage and position. Fans and the pump are checked for bearing wear, and panels and mounts tightened. Worn parts are replaced. We then explain which sounds are part of normal operation and confirm the new noise has stopped.
  18. 18

    Compressor Struggling to Start

    The compressor clicks, hums briefly and stops, or starts only after several attempts, and the machine produces little or no ice. The start components, the supply voltage or the compressor itself may be at fault.

    Likely origins
    failed start relay or capacitor · overload protector tripping · low supply voltage · compressor overheating from a dirty condenser · worn compressor
    The fix
    We measure supply voltage during the start attempt and test the start relay, capacitor and overload. The condenser is cleaned if it is contributing to overheating. Failed start components are replaced. If the compressor itself has failed, we explain the cost against replacing the machine before any sealed-system work. Several starts are observed after the repair.
  19. 19

    Ice Machine Has No Power

    The machine shows no lights and makes no sound. Power is not reaching it, often from a tripped GFCI under a counter, or an internal transformer or control has failed.

    Likely origins
    tripped breaker or GFCI · switch off · failed control board · failed transformer · loose wiring
    The fix
    We check the outlet, GFCI and the machine's own switch, then measure voltage through the transformer to the control board. Wiring and connectors are inspected for heat or moisture damage. The failed transformer, switch or board is renewed. The machine is started and observed through its first fill and freeze to confirm it is running normally.
  20. 20

    Water Escaping Inside the Cabinet

    Water runs out of the freezing compartment into the bin or the base of the cabinet during the freeze cycle. It is being splashed or overflowing from the sump instead of returning to it.

    Likely origins
    water curtain displaced or missing · distribution tube out of position · sump overfilling · cracked sump · splash shield missing after cleaning
    The fix
    We run a freeze cycle with the front panel removed to see where water leaves its intended path. The curtain, splash shields and distribution tube are seated correctly, and the sump level checked. A cracked sump is replaced. The machine is run through a full cycle to confirm water stays within the freezing compartment.
  21. 21

    Production Dropping in Hot Weather

    Output falls during hot weather, when the room or the incoming water is warm. The refrigeration system has to reject more heat in those conditions, and any restriction to airflow magnifies the loss.

    Likely origins
    high room temperature · dirty condenser · poor ventilation · warm incoming water · condenser fan failing
    The fix
    We measure room and incoming water temperatures and compare production with the manufacturer's rating at those conditions. The condenser is cleaned and the condenser fan tested. Ventilation around undercounter units is checked for blocked grilles. Production is then timed so you can see whether the machine is performing as it should for the conditions.
  22. 22

    Water Running Without Stopping

    Water keeps flowing into the machine and out of the drain, even during freezing. The inlet valve is stuck open or the control is holding it on.

    Likely origins
    inlet valve stuck open with debris · valve diaphragm torn · float or level probe fouled · control board fault · purge valve stuck open
    The fix
    Close the supply valve to the machine until it is repaired, especially if water is spilling. We check whether the valve passes water with power removed, which identifies a valve that will not seal. The float or level probe is cleaned and the control's output tested. The faulty component is replaced and a cycle observed.
  23. 23

    Sump Overfilling

    The water reservoir fills beyond its normal level and spills into the bin or straight to the drain. The inlet valve is not closing at the right point, or the level sensing has been fouled.

    Likely origins
    float stuck by scale · level probe fouled · inlet valve slow to close · control fault · machine out of level
    The fix
    We observe a fill and clean the float or level probe, which scale and slime commonly coat. The inlet valve is tested for slow closing, and the machine levelled so the sump reads accurately. A valve that closes slowly, or a sensor that misreads, is renewed. A further fill is observed to confirm the level stops at its mark.
  24. 24

    Ice Machine Freezing Into a Solid Block

    Ice bridges between cubes and builds into a solid mass on the plate, sometimes bending the curtain or jamming the mechanism. A harvest has failed and the machine has kept freezing.

    Likely origins
    harvest valve fault · bin or curtain switch not reporting harvest · scale on the plate · thermistor fault · water supply interruption
    The fix
    Switch the machine off and let the ice melt naturally; never chip it away, as tools can puncture the evaporator. We then test the harvest valve, the curtain switch and the thermistor that end each stage. The plate is descaled. The failed part is replaced, and several freeze and harvest cycles are observed to confirm normal sequencing.

Further entries on file · 16

  1. Hollow or Dimpled Cubes
  2. Cube Sizes Uneven Across the Plate
  3. Water Not Flowing Over the Plate
  4. Harvest Taking Too Long
  5. Ice Forming on the Refrigeration Tubing
  6. Water Collecting in the Ice Bin
  7. Condensate Drain Blocked
  8. Scale Restricting the Water Lines
  9. Slime or Mold Inside the Machine
  10. Production Varies Through the Year
  11. Control Board Fault
  12. Condenser Fan Motor Failed
  13. Curtain Switch Not Registering Harvest
  14. Machine Stopping With an Empty Bin
  15. Ice Machine Tripping the Breaker
  16. Supply Line Frozen

Next step

Sounds like your machine?

A person picks up day or night, seven days a week.

Platforms · 9

Makes of ice maker on our books

These 9 names genuinely produce a ice maker; a pairing that was never manufactured has no page here.

Specification

Ice Maker work, measured

1–2 hours
Usual visit length
9
Brands we repair
119
ZIP codes covered

Price

What ice maker repair costs

  1. Consumable and protective parts

    On an ice maker: No Ice Being Produced · Ice Tasting of Chlorine or Minerals · Condenser Coils Restricted by Dust · Scale Coating the Evaporator Plate

  2. Motors, pumps and mechanical assemblies

    On an ice maker: No Ice Being Produced · Ice Production Falling Short · Water Pooling Under the Machine · Cubes Thin or Undersized

  3. Control electronics and boards

    On an ice maker: No Ice Being Produced · Compressor Struggling to Start · Ice Machine Has No Power · Water Running Without Stopping

  4. Sealed cooling circuit

    On an ice maker: No Ice Being Produced · Ice Production Falling Short · Condenser Coils Restricted by Dust · Scale Coating the Evaporator Plate

Questions

Questions owners ask about ice maker repair

If yours is missing, put it to a coordinator directly.

Something not covered?

The line is staffed at all hours for Nassau and Suffolk.

  • Is there a charge if the appliance cannot be repaired?

    The diagnostic fee buys the visit and the diagnosis itself, which is why it stands even when no repair is carried out — and if one does, the fee is credited toward it. If we conclude the machine is not worth repairing, or that the problem is not in the appliance at all, you are still given a definite answer and the reasons for it, not a shrug. That answer is what the fee pays for.

  • If a breaker trips when the appliance runs, is the appliance faulty?

    Possibly, though often it is not. The machine may have a real fault, or the circuit may be shared or too small, the breaker may be worn and tripping below its rating, or there may be a supply problem further back. Swapping parts until the symptom changes is not a diagnosis. We confirm the appliance is getting a proper supply before blaming it, and if the installation is at fault we say so and refer it to an electrician.

Ice Maker · Long Island

Servicing the ice maker on Long Island

The ice maker symptom that misleads most

Whatever the brand, the ice maker problem most frequently misjudged is an ice maker written off as dead when the water line behind the appliance is kinked or the inlet screen has clogged with mineral deposit. Getting it wrong matters, because a mistaken reading leads to a mistaken part, and on an ice maker that part is often the costliest in the machine.

Book a visit

Describe the machine, then add contact details. Booking is free and places you under no obligation. You can also phone (631) 729-9995 and a dispatcher will note everything for you.

Arrange a ice maker visit

Two short steps. No cost and no obligation to book.

  • Answered 24/7
  • 3-hour arrival window
  • Price approved first
Step 1 of 2

The repair

Which appliance needs repair?

Appliance

Where are you?

Free to book. No payment details needed.

Rather speak to someone? (631) 729-9995

Call now(631) 729-9995Book online