Skip to main content

Phones answered 24/7 · Long Island, NY

Ice Makers · 6 min to read

Refrigerator Ice Maker Stopped Making Ice? Work Through These Checks

Before you assume the ice maker is broken, rule out the shutoff arm, the freezer temperature, the water filter and a frozen fill tube. Most stopped ice makers fail one of those.

Written by PrimeFix Long Island

A refrigerator ice maker is a simple loop: water flows in, freezes in a mold, the ice is pushed out into a bin, and the cycle repeats until the bin is full. When it stops, the cause is usually one point in that loop. Many of the checks take only a few minutes, and several of the most common causes are not failures at all.

This post covers ice makers built into refrigerators and freezers. If you are on a private well, our post on ice makers on well water in Suffolk County covers sediment and water-quality issues that affect ice makers in particular.

1. Is it switched on?

Ice makers have a way of turning off, and it is easy to switch them off by accident.

  • Shutoff arm. Many ice makers have a wire arm or bail that rests on the ice in the bin. When the arm is raised, the ice maker stops. If it was knocked up while you were moving things in the freezer, the ice maker will not make ice. Lower it.
  • Switch or button. Other ice makers have an on/off switch on the ice maker itself, or a setting on the refrigerator's control panel. Check both.
  • Bin sensor. Some models use an optical or infrared sensor instead of an arm. Frost or ice on the sensor, or a misplaced bin, can make it think the bin is full. Reseat the bin and wipe the sensor area according to the manual.

2. Is the freezer cold enough?

Ice makers need the freezer to be cold to freeze water quickly. Many manufacturers recommend a freezer temperature around 0°F. If the freezer is warmer, the ice maker may slow down or stop entirely. Put an appliance thermometer between frozen packages and check it after a few hours. If the freezer is warm, the problem is not the ice maker — see our post on frost building up in the freezer for causes.

3. Is water reaching it?

The supply valve

The water line to the refrigerator usually has a shutoff valve under the sink, in the basement under the kitchen or behind the refrigerator. Make sure it is fully open. If you recently had plumbing work done, it may have been closed.

The water filter

A clogged water filter is one of the most common causes of slow or stopped ice production. Water may still trickle through the dispenser, but too slowly for the ice maker to fill properly. If the filter is past its replacement date — many manufacturers suggest roughly every six months, but check yours — replace it.

If you just replaced the filter and ice stopped, check that it is fully seated and locked, and that it is the correct filter for your model. A filter that is not seated can block water flow entirely. After replacing a filter, many manuals recommend flushing several gallons through the dispenser to clear air and carbon fines.

Kinks in the line

If the refrigerator was recently moved or pushed back, the supply line behind it may be kinked. Pull it out carefully and check.

Low water pressure

The water inlet valve on a refrigerator needs a minimum water pressure to open properly; the figure varies by model and is in the installation manual. Low household pressure, a partly closed valve or a restricted filter can all leave the ice maker underfilled.

4. Is the fill tube frozen?

Water enters the ice maker through a small fill tube. If water drips slowly — because of low pressure or a leaking inlet valve — it can freeze inside the tube and block it. You may see a plug of ice at the end of the tube where it enters the ice maker, or in the tube behind it.

You can sometimes thaw a frozen fill tube with a hair dryer on low, held at a safe distance, or by following the procedure in your manual. Keep water and electrical parts apart. If the tube refreezes after you clear it, the cause — often a failing water inlet valve or low pressure — needs to be fixed.

5. Is ice jammed in the ice maker or the bin?

Ice can jam in the ice maker's mold, or clump together in the bin, especially if the ice maker has not been used for a while or the freezer temperature has fluctuated. Clumped ice can also stop the dispenser auger. Empty the bin, break up clumps, and wipe out any water. Check whether ice is stuck in the mold or the ejector.

6. Is it new, or was it recently restarted?

A new ice maker, or one that has been off, often takes a while to start producing. Many manufacturers say it can take up to a day or so for the first ice to appear, and recommend discarding the first few batches. If you have just installed a refrigerator or reconnected the water line, give it time.

When the ice maker itself has failed

If you have checked the switch, the temperature, the water supply, the filter and the fill tube, and there is still no ice, a part may have failed:

  • The water inlet valve at the back of the refrigerator may not be opening. A buzzing sound with no water flow can be a sign.
  • The ice maker module — the motor, thermostat or control that runs the cycle — may have failed. Many are replaced as a single assembly.
  • The control board may not be signalling the ice maker.
  • A door-mounted ice maker on some French-door refrigerators has its own fan and seals, which can cause separate problems.

Leaks and bad-tasting ice

If the ice maker is making ice but also leaking, see our post on water leaking under the refrigerator. If the ice tastes or smells off, start by replacing the water filter and emptying the bin, since ice absorbs odors from the freezer.

You can book an ice maker repair visit or read about our ice maker repair service across Nassau and Suffolk.

Continue with

Call now(631) 729-9995Book online