An electric cooktop with one burner that will not heat is a common call. Sometimes the whole cooktop stops; more often it is a single element, while the others work fine. That pattern is useful, because it rules out the house wiring and narrows the problem to the parts that serve that one burner.
This post covers electric coil cooktops and radiant glass cooktops. Induction cooktops work on a different principle and have their own troubleshooting; our post on switching from gas to induction explains how they work.
Safety first
Turn the cooktop off and let it cool completely before touching any element. For anything more than removing and swapping a coil burner, turn the cooktop off at the circuit breaker. Electric cooktops run on 240-volt circuits, and the wiring under the top is not a place to work with the power on.
When the whole cooktop is dead
If none of the elements heat, start at the breaker panel. Electric cooktops are usually on a double breaker. If one half has tripped, some elements may work and others may not, or the whole cooktop may stop. Turn the breaker fully off and back on. If it trips again, stop and call — that suggests a short somewhere. If your cooktop has a control lock or child lock, also check that it has not been switched on by mistake.
Coil element cooktops
Coil burners plug into a receptacle, often called a terminal block, under the drip pan. That makes them easy to test.
The swap test
- Make sure the cooktop is off and all elements are cool.
- Lift the non-working coil element slightly and pull it straight out of its receptacle.
- Take a working element of the same size from another position and plug it into the non-working position.
- Turn that burner on.
- If the borrowed element heats, the original element has failed. Replacing it is usually a matter of buying the correct element for your model and plugging it in.
- If the borrowed element does not heat in that position, the problem is not the element. It is the receptacle, the wiring or the control switch for that burner.
Look at the receptacle and the element terminals
While the element is out, look at its terminals and at the receptacle. Burned, blackened, pitted or melted terminals point to a poor connection, which can overheat and eventually fail. If the receptacle is damaged, replace it along with the element — a new element plugged into a burned receptacle will often burn again.
Inspect the element itself
A coil element with a visible blister, a split, or a spot that sparked or bulged has failed. Do not use it.
Radiant glass cooktops
On a smooth glass cooktop, the elements are under the glass, so you cannot swap them as you can with coils. But you can still learn a lot.
Watch what the element does
- It does not glow at all. The element, its control switch or a wiring connection is likely at fault.
- It glows on high but not on low or medium. On many models, the control switch — often called an infinite switch — cycles power on and off to set lower heat. A failing switch can stick fully on or fully off.
- It stays on high no matter what. This usually points to the control switch or a relay on the control board, and is a safety issue. Stop using it.
- Only part of a dual or triple element heats. Many radiant elements have more than one ring, controlled separately. Either one of the rings or the selector switch has failed.
The limiter
Many radiant elements have a built-in limiter that cuts power to protect the glass if it gets too hot. If the limiter fails, the element may stop heating or cycle off too often. A limiter is usually part of the element assembly.
The hot surface light
The hot surface indicator stays on while the glass is hot. If it stays on long after the cooktop is cool, or never comes on, the indicator or the control may be faulty, even if the elements themselves work.
Check the glass
If you see a crack in the glass, stop using the cooktop and turn it off at the breaker. A cracked glass top is a safety issue, as liquid can reach the elements and wiring below. Our post on caring for a glass-top stove covers how to avoid damage in the first place.
Touch-control cooktops
Many newer cooktops use touch controls and an electronic control board rather than knobs and individual switches. If one burner will not respond to the controls, or the controls show an error code, the control board, a sensor or the touch panel may be the cause. Spills that dry on the control area can also interfere with touch pads — clean the panel as the manual describes and try again. Error codes and their meanings are usually listed in the manual.
What not to do
- Do not attempt to work on the wiring under the glass with the power on.
- Do not use a cooktop with a cracked glass top, a sparking coil, or an element that will not turn off.
- Do not wrap drip pans or elements in aluminum foil, which can cause overheating and damage the receptacle.
When to call
Replacing a coil element after a swap test is a reasonable homeowner job. Replacing receptacles, control switches, radiant elements, limiters or control boards involves working inside the cooktop with 240-volt wiring, and that is where a technician should step in. Having the model number ready — usually on a label under the cooktop, on the side of the burner box or on the front frame — helps us bring the right parts.
You can book a cooktop repair visit or read about our cooktop repair service across Nassau and Suffolk.