A gas oven that once heated quickly now takes longer and longer before the burner lights, and the oven takes ages to reach temperature or never quite gets there. That pattern is common, and the cause is usually not the gas supply or the oven's control. It is often the igniter, a part that wears gradually and gives plenty of warning before it fails.
How a gas oven lights
Many gas ovens in North American homes use a hot-surface igniter, commonly called a glow bar. When you turn the oven on, electricity flows through the igniter and it heats up until it glows bright orange. In many designs, the igniter is wired in series with the oven's gas safety valve. The valve only opens when enough current is flowing through the igniter — which only happens when the igniter is hot enough to light the gas. When the valve opens, gas flows to the burner, the hot igniter lights it, and the oven heats.
This is a safety feature: the valve will not let gas flow unless there is a hot enough source to ignite it.
Some ovens use a spark igniter instead, which clicks like a gas cooktop burner, with a sensor to confirm the flame. If your oven clicks when it lights, the advice below about the glow bar may not apply; check your manual.
Why the igniter gets slower
As a hot-surface igniter ages, its electrical resistance changes, and it draws less current. It may still glow, and even look bright, but not draw enough current to open the gas valve quickly. The result is a delay: the igniter glows for longer and longer before the valve opens and the burner lights. Eventually it may not open the valve at all.
Common signs include:
- the igniter glows but the burner takes a long time to light, or does not light;
- the oven takes much longer to preheat than it used to;
- the oven does not reach the set temperature, or drops below it during cooking;
- you hear a louder than usual whoosh or a soft bang when the burner finally lights.
The last one deserves attention. If gas builds up for a moment before lighting, the ignition is louder. A soft, quick light is normal. A loud boom is not, and you should stop using the oven until it is checked.
What you can check safely
Look at the igniter while it works
On many ovens, the bake burner and igniter are under the oven floor panel. On some, you can see the igniter through a slot or by removing the floor, as the manual describes. With the oven cold, turn it to bake and watch:
- No glow at all. The igniter may have failed completely, or it is not getting power. That can be the igniter, the wiring or the control.
- Glows, but no flame after a minute or more. The igniter is likely too weak to open the gas valve.
- Glows and lights promptly. The igniter is probably fine, and the problem is elsewhere.
Normal light-off times vary by model, so the trend matters more than any number — if yours is getting slower month by month, that is the igniter wearing.
Check the broiler too
Many gas ovens have a separate broil burner with its own igniter, usually at the top of the oven or in a drawer below. If baking is slow but broiling lights fine, the bake igniter is the likely suspect, and vice versa.
Make sure the oven has gas
If the cooktop burners light normally, the gas supply to the range is probably fine. If nothing on the range lights, check whether the gas supply valve behind the range is open, and whether there is a wider gas issue.
What not to do
- Do not touch the igniter. It is fragile and gets extremely hot. Skin oils and bumps can damage it.
- Do not light the oven burner with a match unless your manual specifically describes that procedure. Many modern gas ovens with hot-surface ignition are not designed to be lit manually; the gas valve may not open without the igniter.
- Do not keep restarting the oven if the igniter glows and nothing lights. Turn it off and get it checked.
- Do not attempt to adjust or replace the gas valve or connections yourself.
If you smell gas
A faint whiff of gas for a moment just before the burner lights can be normal. A strong or continuing smell of gas is not. If you smell gas in the house, do not use any switches, appliances or phones inside. Leave the house and call your gas utility or 911 from outside. Our post on gas range safety on Long Island explains what to do in more detail.
Is the igniter a DIY repair?
Replacing a hot-surface igniter involves removing the oven floor or a rear panel, unbolting the igniter from the burner, and connecting the wiring. It is close to the gas burner and valve, and the replacement must be the right part for the model so that it draws the correct current for that valve. Many homeowners would rather have a technician do it, and we recommend that, particularly because a technician can also confirm the gas valve and the burner are working properly.
Before a big cooking day
Igniters tend to give out at the worst time — when the oven is working hardest. If your oven has been slow to light, have it checked before a holiday meal rather than on the morning of it. Our post on testing and calibrating your oven can help you tell an igniter problem from a calibration one.
You can book an oven repair visit or read about our oven repair service across Nassau and Suffolk.