Skip to main content

Phones answered 24/7 · Long Island, NY

Washers · 6 min to read

Washer Shaking, Banging or Walking Across the Floor? Start Here

A washer that thumps and travels during the spin cycle is usually telling you about the load, the legs or the floor before it is telling you about a broken part.

Written by PrimeFix Long Island

Few appliance noises are as alarming as a washer that bangs against the wall during the spin cycle and then shuffles a few inches across the floor. It sounds like something is about to break. Sometimes something already has — but more often the cause is one of a handful of simple things, and the machine is fine once they are fixed.

A washer drum spinning at high speed with wet laundry inside is a heavy, fast-moving mass. If that mass is off-center, or the machine is not firmly planted, the forces have to go somewhere. Here is how to work out where.

Is it brand new, or newly moved?

If the shaking started right after the washer was installed or moved, check this before anything else.

Shipping bolts

Most front-load washers ship with transport bolts through the back panel that lock the drum in place so it is not damaged in transit. They are supposed to be removed during installation, and the installation manual shows where they are. A front-loader run with those bolts still in place shakes violently, because the drum cannot move on its suspension at all. Look at the back of the machine: if there are bolts or plastic spacers in the positions your manual shows, they need to come out. Keep them — you will need them if you ever move the washer again.

Some top-loaders use packing blocks or straps instead. Check the manual for your model.

Leveling

A washer that rocks even slightly on its legs will shake on spin. Grab the top corners and try to rock it diagonally. If it moves, it is not level.

Most washers have adjustable front legs, each with a locking nut. Many also have self-adjusting rear legs. To level it:

  1. Put a level on top, front to back and side to side.
  2. Loosen the lock nuts on the front legs and screw the legs in or out until the machine sits level and does not rock.
  3. Tighten the lock nuts up against the cabinet, so the legs cannot turn on their own during spin. This step is often skipped, and it is the reason a washer that was level gradually walks out of position.
  4. If your model has self-adjusting rear legs, your manual may tell you to tip the machine forward gently and set it down to let them adjust.

Is it only certain loads?

If the washer shakes only some of the time, look at what is in it.

  • Single heavy items. One bath mat, a pair of jeans, a dog bed or a comforter can bunch up on one side of the drum. Washing a heavy item alone is a common cause of a lopsided spin. Adding a couple of towels to balance it often helps.
  • Water-absorbent bulky items. Comforters and pillows soak up water unevenly. Check your manual for whether your washer is rated for them at all, and follow its bulky-item cycle.
  • Small loads. A very small load can be just as unbalanced as a big one.
  • Overloading. In a top-loader, laundry wrapped tightly around the agitator or packed against one side cannot redistribute.

Many modern washers detect an unbalanced load, pause, try to redistribute it, and may stop with an error code or spin at a lower speed. That is the machine protecting itself, not a failure.

Is it the floor?

The floor matters more than most people expect. A washer on a slab in a basement sits on something very rigid. A washer on a wood-framed floor — a second-floor laundry, a mudroom over a crawl space, or a laundry area on an upper level of a raised house — can make the floor itself flex during spin, which magnifies vibration.

  • Make sure the washer is sitting on the floor itself, not on a piece of plywood, a carpet remnant or a soft mat that lets it rock.
  • Many people use anti-vibration pads under the feet; if you do, follow the pad maker's instructions and make sure they do not lift the washer off its leveled legs.
  • If the floor visibly bounces, that is a structural question for a contractor rather than an appliance fix.

When it is the washer

If the load is balanced, the legs are level and locked, the shipping bolts are out and the floor is solid, worn suspension parts are the likely cause.

  • Top-load washers usually hang the tub on suspension rods or springs at the corners. When those wear, the tub sags to one side or bounces loosely, and even balanced loads cause banging. A tub that sits visibly off-center when the machine is empty is a strong sign.
  • Front-load washers use springs above the drum and shock absorbers or dampers below. Worn dampers let the drum move too much, and you may hear it knock against the cabinet.
  • Drum bearings in a front-loader can wear and produce a loud rumble or roar that gets worse at high spin speed. Water or rust streaks on the back of the drum area can be a sign of a failing seal. Bearings are a substantial repair, and whether it is worth it depends on the age and condition of the machine.

These parts are reached by opening the cabinet, and a technician can tell you quickly whether they are worn.

Stacked washers and dryers

A stacked pair adds height and leverage, so vibration from the washer is felt more strongly at the top. Use the stacking kit the manufacturer specifies, make sure the washer underneath is level and its legs are locked, and do not stack combinations the manufacturer does not approve.

Why not just ignore it?

A washer that walks can pull on its drain hose, its water supply hoses and its power cord. Hoses can pull loose, and a washer that bangs against a wall can damage both. Repeated hard knocking also wears the suspension faster. It is worth fixing promptly.

Next steps

Check, in order: shipping bolts if new, leveling and lock nuts, the load, and the floor. If the washer still shakes with a balanced load on a solid floor, you can book a washer repair visit or read about our washer repair service across Nassau and Suffolk.

Continue with

Call now(631) 729-9995Book online