Dishes Coming Out With Food Still On Them? Clean These Two Parts First
When a dishwasher stops cleaning well, the cause is usually not the dishwasher wearing out. It is a clogged filter, blocked spray arms, or a load that never lets the water reach the plates.
A dishwasher that once cleaned well and now leaves bits of food on plates and grit in the bottom of glasses is frustrating, because it seems to get worse the more you use it. That is a clue in itself. Gradual decline usually means something is slowly clogging, not something suddenly breaking. Two parts account for most of it: the filter and the spray arms.
How a dishwasher cleans
A dishwasher does not scrub. It fills a small amount of water in the bottom of the tub, heats it, and a pump forces it through the spray arms, which spin and blast water up at the dishes. That water drains back to the bottom, passes through a filter, and gets pumped around again. If the filter clogs, the pump has less water to work with. If the spray arm holes clog, the water cannot reach the dishes with enough force. Either way, food stays on.
1. Clean the filter
Many dishwashers sold in recent years have a manual-clean filter that you are expected to clean yourself. Older dishwashers, and some current ones, use a self-cleaning filter with a grinder. If you have never removed yours, check your manual — there is a good chance it needs attention.
On most models the filter sits in the floor of the tub, under the lower spray arm. Typically you:
Remove the bottom rack.
Twist the cylindrical filter counterclockwise and lift it out; a flat mesh filter often comes out with it.
Rinse both under warm running water, using a soft brush and a little dish soap for greasy film. Avoid wire brushes or scouring pads, which can damage the mesh.
Look into the filter opening and remove any glass, bones, fruit pits or labels.
Reinstall the filter, making sure it locks fully in place. A filter left loose can let debris into the pump.
Manufacturers' recommended intervals vary from monthly to every few months, depending on how much you use it and how much food goes in. If you can see a layer of debris on the filter, you are overdue.
2. Clear the spray arms
Spray arms have small holes that clog with seeds, bits of paper label, hard-water scale and food. Check them:
Do they spin freely? Turn each arm by hand. It should rotate without catching.
Are any holes blocked? Look closely, and hold an arm up to the light.
Most lower spray arms lift or twist off, and upper arms usually unscrew or unclip. Check your manual. Rinse the arm under the tap and clear any blocked holes with a toothpick or a straightened paper clip; shake debris out of the arm. If you see white mineral scale, soaking the arm in white vinegar can loosen it. Reinstall it firmly.
On some models there is a third spray arm or a wash zone at the top of the tub; give it the same treatment.
3. Look at how it is loaded
Even a perfectly working dishwasher cannot clean what the water cannot reach.
Spray arm clearance. Tall pans, cutting boards or a handle hanging through the rack can stop a spray arm from turning. After loading, spin the arms by hand to be sure they are free.
Facing the spray. Bowls and pots should face down and inward toward the center, where the water comes from.
Overcrowding. Nested bowls and spoons that stack inside each other shield each other from the water.
The detergent door. Big plates or a tray in front of the dispenser can stop it from opening fully, or stop the detergent from washing out.
4. Check the water temperature
Dishwasher detergents work best in hot water. Many manufacturers recommend the water reaching the dishwasher be at least around 120°F, though your manual will give the figure for your model. Running the kitchen tap until it is hot before starting the dishwasher means the first fill is hot rather than cold water that was sitting in the pipes. That matters especially in kitchens far from the water heater.
5. Check the detergent
Old detergent loses its effectiveness. Powder that has clumped from humidity — a real issue in a Long Island summer — does not dissolve well.
Pre-rinsing. Scraping off large food is sensible. Many detergent makers say that scrubbing dishes completely clean first is unnecessary, because the enzymes in modern detergents are designed to work on food soil.
6. Is the dishwasher draining?
If water stays in the bottom of the tub, or you see dirty water after a cycle, the dishwasher is recirculating dirty water. That is a drain problem rather than a cleaning one. See our guide to a dishwasher that won't drain, which covers the disposal, the air gap and the high loop.
When it is a part
If the filter and spray arms are clean, the loading is right, the water is hot and the dishwasher still does not clean, something mechanical may be failing:
a weak or failing circulation pump, which may sound quieter than normal during the wash;
a water inlet valve that underfills the tub, so there is too little water to circulate;
a heating element that does not heat the water;
a broken spray arm mount or a cracked arm;
a detergent dispenser that does not open.
These are the points to have it checked. When you book, tell the technician what you have already cleaned and whether the problem is the bottom rack, the top rack or both — that pattern helps narrow it down. You can book a dishwasher repair visit or read about our dishwasher repair service across Nassau and Suffolk.