Opening the dishwasher to find a pool of gray water in the bottom is one of the most common appliance complaints in any kitchen. The dishwasher may be at fault — but very often the problem is somewhere between the dishwasher and the drain, in parts that have nothing to do with the machine itself.
Work through these in order. Each one is quick, and several can be done without tools.
First: is it actually a problem?
A small amount of water left in the sump, below the filter, is normal on many dishwashers. It keeps seals moist. What is not normal is water above the filter, covering the floor of the tub, especially if it smells or has food debris in it.
Also check whether the cycle actually finished. If the power was interrupted or the door was opened mid-cycle, the machine may simply not have reached its drain step. Run a drain or cancel cycle — your manual explains how — and see if it empties.
1. Clean the filter
Most dishwashers built in the last decade or so have a manual-clean filter at the bottom of the tub, under the lower spray arm. If it has never been cleaned, it may be nearly blocked with food, glass fragments, labels and grease. A clogged filter stops water reaching the drain pump.
Twist out the filter, rinse it under hot running water, and scrub the mesh gently with a soft brush. Check the sump below it for broken glass or bone. Reinstall it firmly — a loose filter can let debris into the pump.
Manufacturers generally recommend cleaning these filters regularly; if you do heavy pre-rinsing less often, it needs it more often.
2. Check the sink and disposal
The dishwasher drain hose usually connects either to the garbage disposal or to a fitting on the sink's drain tailpiece. If that drain is slow, the dishwasher cannot empty into it.
- Run the disposal with cold water for a few seconds. Food left in the disposal chamber can block the dishwasher inlet.
- Fill the sink and let it drain. If the sink is slow too, the clog is in the household drain, which is a plumbing call rather than an appliance one.
3. The knockout plug on a new disposal
This one catches people out constantly. A new garbage disposal comes with a plug sealing its dishwasher inlet, so that it does not leak if there is no dishwasher. The plug has to be knocked out before the dishwasher hose is connected.
If your dishwasher stopped draining immediately after a new disposal was installed, this is almost certainly why. The water has nowhere to go and may back up into the sink or out of the air gap.
Disposal manufacturers explain that the plug is easiest to remove before the disposal is mounted, but it can be done afterwards: disconnect power to the disposal, disconnect the dishwasher hose, and knock the plug inward with a screwdriver, then retrieve it from the disposal chamber so it does not jam the grinder. If you are not comfortable working under the sink, this is a short visit.
4. The air gap
Many Long Island kitchens have a small chrome or plastic cylinder on the countertop or sink deck next to the faucet. That is an air gap. The dishwasher drains up into it and back down to the disposal or sink drain. Its job is to stop dirty sink water being siphoned back into the dishwasher.
Air gaps clog. Food and grease build up inside them, and when they block, water may spill out of the air gap onto the counter during the drain cycle, or the dishwasher may not drain at all.
To clean one, pull off the decorative cap, unscrew the inner cover if there is one, and clear any debris. You can also disconnect the hoses under the sink and flush them through.
5. The high loop
If you do not have an air gap, the drain hose should be looped up as high as possible under the counter — fastened to the underside of the countertop or high on the cabinet wall — before it drops to the drain connection. This "high loop" does a similar job to the air gap: it stops sink water from flowing back into the dishwasher.
Without that loop, you may see dirty water in the dishwasher even when it has not been used, especially after running the sink or disposal.
Which approach your kitchen should have depends on the plumbing code enforced in your town and on the dishwasher's installation instructions. Either way, the drain hose should never sag down to the floor and back up.
6. Check the drain hose
Look at the hose under the sink and, if you can, behind the dishwasher. Kinks often happen when a dishwasher is pushed back into its opening after installation. A kinked or crushed hose restricts flow. If the hose has been in place for years, it may also be clogged internally with grease. Replacing it is not expensive.
When it is the dishwasher
If the filter is clean, the sink drains freely, the knockout plug is out, the air gap is clear and the hose is straight and properly looped, the problem is probably inside the machine:
- The drain pump has failed. You may hear it humming without moving water, or hear nothing at all during the drain step.
- Something is jammed in the pump. Glass, a cherry pit or a piece of plastic in the impeller can stop it.
- A check valve is stuck. Many dishwashers have a one-way valve at the pump outlet that can stick closed.
- A control or wiring fault means the pump is never told to run.
- An error code is displayed. Many dishwashers report drain faults with a code; the manual tells you what it means.
These are routine dishwasher repairs.
A few prevention habits
- Scrape plates rather than rinsing them perfectly — but do scrape. Bones, pits and labels are what block filters.
- Clean the filter regularly.
- Run the disposal before starting the dishwasher.
- Run hot water at the sink until it is hot before you start a cycle, so the dishwasher fills with hot water from the beginning.
If you have worked through this list and the water is still sitting there, book a visit. Tell us what you have already checked; it saves time on the day.