Skip to main content

Phones answered 24/7 · Long Island, NY

Ranges · 5 min to read

Gas Burner Keeps Clicking or Won't Light? Usually It Is Water, Food or a Misplaced Cap

A gas range burner that clicks without lighting, or keeps clicking after it lights, is very often a cleaning problem rather than a broken part. Here is what to check, in order.

Written by PrimeFix Long Island

Most gas ranges light their surface burners with a spark. Turn the knob, and an electrode next to the burner snaps a small spark across to the burner, which lights the gas. That clicking is normal while you light a burner. Two things are not: a burner that clicks and clicks but will not light, and a burner that keeps clicking after the flame is lit, or clicks when no burner is on at all.

Both are common, and both are very often caused by something simple: water, food, or a burner part that is not sitting where it should.

Safety first

If a burner does not light within a few seconds, turn the knob off. Do not let unlit gas flow while you keep trying. Wait a minute or two for the gas to disperse before trying again.

If you smell gas strongly at any time, turn the burner off, do not use any switches or appliances, leave the house and call your gas utility or 911 from outside. Our post on gas range safety on Long Island covers this in more detail.

Before cleaning or removing burner parts, make sure all burners are off and cool. If you are working near the igniters, it is wise to unplug the range or turn off its circuit.

Clicks but won't light

Burner cap out of position

On sealed-burner ranges, each burner has a base and a separate cap that sits on top. If the cap is slightly off-center or tilted — which happens easily after cleaning — the gas does not flow out of the ports evenly, and the spark may not reach it. Lift the cap off, make sure it is clean, and set it back so it sits flat and centered. Many caps have notches or pins that need to line up with the base; the manual shows how.

Clogged burner ports

Food boil-overs, grease and cleaning residue can block the small ports around the burner head. Remove the cap and burner head if your model allows, and gently clear the ports with a straight pin or a thin wire. Avoid toothpicks, which can break off inside the ports. Do not enlarge the holes. Wash the parts with warm soapy water and let them dry completely before reassembling.

Wet burner or igniter

Water from a spill or from cleaning can wet the burner and the igniter. A wet igniter may not spark properly, and a wet burner may not light. Let the parts dry thoroughly — this can take a few hours. Do not put wet burner caps back on the range.

A dirty or cracked igniter

Look at the igniter electrode — usually a small white ceramic post with a metal tip next to the burner. Grease or residue on it can stop it sparking well. Wipe it gently with a dry cloth or a soft toothbrush. If the ceramic is visibly cracked, the igniter needs replacing.

Look at the spark

With the room dimmed, turn the knob to the light position and watch the igniter. You should see a strong, regular spark. A weak spark, no spark at that burner, or a spark that jumps to the wrong place points to a failing electrode, a bad wire or a weak spark module.

Keeps clicking after it lights

Moisture in the switch

A very common cause, especially after a boil-over or after cleaning the cooktop with a lot of liquid. Water or cleaning solution runs down around a knob into the spark switch behind it, causing the igniters to keep clicking even when the burner is lit, or when every burner is off. Unplug the range or turn off its circuit, take off the knobs, and let it dry thoroughly. A few hours or overnight is often enough. Avoid spraying cleaners directly on the knobs or control panel; spray a cloth instead.

Flame not sensed

On some ranges, the igniter stops clicking once the system senses a flame. If the burner is dirty or the cap is misaligned, the flame may not be steady enough to be detected, and the clicking continues. Cleaning and reseating usually solves it.

A failing switch or spark module

If the range keeps clicking after everything is dry and clean, a spark switch or the spark module may have failed. Those are electrical parts, and replacing them is a job for a technician.

Flames that look wrong

A healthy gas burner flame is mostly blue, steady and even around the burner. Watch for:

  • Yellow or orange, lazy flames that leave soot on pans. This can indicate poor combustion, and should be checked.
  • Uneven flames, tall on one side and missing on the other. Usually the cap is misplaced or ports are clogged.
  • Flames that lift off the burner or blow out easily.

A range that was converted between natural gas and propane needs the correct orifices for its fuel. Flames that are badly wrong after a conversion or a move are a reason for a service visit.

During a power outage

Spark igniters need electricity, so in a power outage they will not spark. Many gas range manuals explain how to light the surface burners carefully with a match during an outage. Follow your own manual exactly, and only if it describes the procedure. Oven burners are a different matter; many cannot be lit manually.

When to call

Clean, dry and reseat first. If a burner still will not light, the spark is weak or missing, the clicking will not stop when everything is dry, or the flames look yellow or uneven, it is time for a technician. You can book a range repair visit or read about our range repair service across Nassau and Suffolk.

Continue with

Call now(631) 729-9995Book online