A dryer that still runs, still tumbles and still feels warm but leaves towels damp after a full cycle is easy to live with — you just hit start again. But it is costing you time and energy, and in some cases it is a warning that hot, lint-laden air is not getting out of the house the way it should. The good news is that the most common causes are things you can check yourself, in an hour or less.
Work through these roughly in order, from the easiest to the most involved.
1. The load and the washer
Start with what goes into the dryer.
- Is the washer spinning properly? If clothes come out of the washer heavier and wetter than usual, the dryer has far more water to remove. A washer that is not reaching full spin speed — because of an unbalanced load, a drain problem or a fault — makes a healthy dryer look broken. Our guide to cleaning a front-loader's drain pump filter covers one common cause.
- Is the drum overloaded? Clothes need room to tumble through the airflow. A drum packed full dries slowly and unevenly, often leaving damp balls of fabric in the middle.
- Are you mixing fabrics? Heavy towels and jeans dry far more slowly than shirts. In a mixed load, the sensor may stop the cycle when the light items are dry, leaving the heavy ones damp.
2. The lint screen
Everyone knows to empty the lint screen, but fewer people know it can clog even when it looks clean. Dryer sheets and fabric softener can leave a nearly invisible film on the mesh that blocks air. Test it by running a little water over it: if water pools on the screen instead of passing through, wash it with warm water, a little dish soap and a soft brush, then let it dry completely before putting it back.
While it is out, look into the lint screen housing with a flashlight. Lint, socks and small items can collect down there. A long, flexible lint brush made for the purpose can reach much of it.
3. The vent
This is the most frequent cause we find, and the most important one to fix, because lint is flammable and a restricted vent traps heat.
Check the vent outside while the dryer is running on a heat setting. You should feel a strong, warm flow of air and see the hood flap open fully. A weak puff of air, or a flap stuck closed with lint or a bird's nest, means the vent is restricted somewhere between the dryer and the outside.
Inside, look behind the dryer. The transition duct — the short connector between the dryer and the wall — is often crushed when the dryer is pushed back. Flimsy plastic or foil accordion ducting traps lint in its ridges; many dryer manufacturers specify rigid or semi-rigid metal duct instead, so check your installation instructions.
Long Island houses add their own vent problems: long runs through split-levels and raised ranches, vents that exit through a roof, and dryers moved up a floor in homes raised after storms. We go through those in detail in dryer vents in split-levels, raised ranches and elevated homes. As a rule, have the full run cleaned if it has not been done in a long time, or if it is long, turns several corners or exits through the roof.
4. The moisture sensor
Many dryers decide when to stop using a pair of metal strips, usually inside the drum near the lint screen. Wet clothes brush against them and complete a tiny electrical circuit; when the clothes are dry, the contact stops and the dryer winds down. Over time, residue from fabric softener and dryer sheets coats the strips, and the dryer can conclude the clothes are dry too early.
Unplug the dryer, find the strips and wipe them clean. Many manufacturers suggest a soft cloth with a little rubbing alcohol or a mild cleaner; check your manual for what it recommends. If your dryer has stopped cycles early and timed dry works better than sensor dry, this is a strong clue.
5. The heat
If the drum is only lukewarm, or the dryer heats sometimes and not others, the heat source may be weakening.
- Electric dryers need two legs of 240-volt power. If one half of the double breaker trips, many dryers will still turn and tumble but produce little or no heat. Check the breaker panel and reset it fully — off, then on.
- Inside an electric dryer, a failed heating element, a high-limit or thermal fuse that has opened, or a cycling thermostat can each cause no heat or low heat.
- Gas dryers use an igniter and gas valve coils. When those weaken, the flame may light late or drop out partway through, which shows up as long, inconsistent drying times.
Thermal fuses often blow because a vent was restricted. If you replace one without fixing the airflow, the new one may blow again. Heating parts and gas components are the point where we recommend calling a technician, especially on gas units.
Warning signs to take seriously
Stop using the dryer and get it checked if:
- the top or sides of the cabinet get very hot to the touch;
- you smell burning or hot dust;
- clothes come out much hotter than usual;
- you find lint accumulating behind the dryer or outside the vent hood.
Getting back to one cycle
Most of the time, a two-cycle dryer gets fixed by some combination of washing the lint screen, cleaning the sensor strips, straightening or replacing the transition duct, and cleaning the vent run. If you have done those and it still runs long, or there is no heat at all, you can book a dryer repair visit or read more about our dryer repair work across Nassau and Suffolk.